Tutorial: Basic introduction to HyperWorks Student Edition. Theory 3D: When to use 3-D Elements, DOFs for Solid Elements, Quality Checks for 3-D. Page: 1 2 3 4 5 6 7 8 9 10 11 Results. Filter by: Product. Altair. All Altair Products Activate AcuSolve. Automated Reporting Director Collaboration and. Altair HyperMesh is a high-performance finite element pre-processor process by eliminating the need to perform manual geometry cleanup and meshing. . over 10 million property records spanning in excess of , materials. Overview.
|Genre:||Health and Food|
|Published (Last):||17 April 2015|
|PDF File Size:||18.28 Mb|
|ePub File Size:||4.23 Mb|
|Price:||Free* [*Free Regsitration Required]|
Make the AlignOnly collector current and the only collector visible. Select the Minimum number of nodes around the hole check box. FluxMotor Brochure FluxMotor is a flexible open software tool dedicated to the pre-design of electric rotating machines. Information can be queried, displaced and even graphed in numerous windows allowing for tutofial geared toward the desired audience.
Only those parts of a component which are essential for the required flux of force and necessary stability are generated. From the graphics area, select the plate you want to isolate. Using the Geometry and Elements Icons, hypemresh on and off components. If the results of the fixes are acceptable, click on Close to exit from Tetra Mesh Optimization utility The imprint subpanel allows you to cause mesh from different, overlapping components to sync or line up with each other, in order to facilitate better connection modeling between them.
Hypermesh Manual | Gonzalo Anzaldo Muñoz –
In a very intuitive interface, it allows defining a machine from templates, creating its winding, and characterizing its performance in a few clicks. When you enter the Plate Edit panel, HyperMesh organizes the surfaces into components that reflect their plate type.
Basics HyperMesh Desktop d. Selecting the same surfaces in both surfs: To review the generated midsurface, hide the Body.
A table layout is used to specify each job, along with options that apply to the entire run. View the model in topology display toolbar to evaluate its integrity.
Hypwrmesh changes that you make to the threshold values in the Element Quality View will not affect the values in the criteria file, but any changes that you make to the criteria file will affect the Element Quality View.
The elements will be created on the mid-planes of each section In this exercise, you will learn how to: Elements having a jacobian of less than 0. With a properly enclosed model, the Volume tetra sub-panel will automatically select the entire volume and hhypermesh a mesh to be created. To open the Plate Edit panel, click plate edit in the auto midsurface subpanel.
Tutorials & Downloads
Post-Processing Post-Processing is where the results of the solver solution can be reviewed and analyzed. Altair HyperMesh was used for finite element preprocessing mesh generation, with Altair HyperView providing post-processing and visualization solutions. Windowing functions, resampling and extracting the local maxima positions to file are supported. From the plate type drop-down menu, select a new plate type based on the geometry.
Note the locations where the mesh was not created in rows and columns of quads. The cell squish criteria describes the non-orthogonality of an element with respect to its faces for 3D elements or edges for 2D elements.
Searched for surfaces that act as a fillet between other surfaces and tangentially extends them to achieve a sharp corner. A circle is generated through the three corner points of the actual triangle.
Or Click not a trim surface. Using this tab the user can export data in the following format: This will result in better mesh quality as will be shown in the next chapter.
Ninety degrees minus the minimum angle found is reported.
All elements on either side of the part are the same color, red or blue. If it does not work, click in the graphics window and then press F. HyperMesh calculates tetra collapse by the following procedure.
Equivalence and Toggle will solve most of the problems.
This has hyprrmesh its use and accuracy many fold. For example, if a group of surfaces are assigned the plate type Planar, but the offset plate will provide better results, you can change its plate type to offset.