ATTANSIC ATTP1 PDF

, 13, ATTANSIC, -. Kring Electronics Co., Ltd. , -, Attansic, sop8. 63, 0, ATTANSIC, -. Rantle East Electronic. , -, ATTANSIC, SOP. 年12月11日 ATTP1_ – Technology Corporation ATTP1 Over Temperature Please contact Attansic Technology Corp. for the latest documents. Attansic. ATTP1. Tel:. MFG:. ATTANSIC. Picture. D/C:. 09+. QTY:. Packaging:. SOP8L. Package:. Note:. 原装正品. Support. No“ATTP1”Picture.

Author: Malazragore Dakinos
Country: Saudi Arabia
Language: English (Spanish)
Genre: Health and Food
Published (Last): 6 June 2011
Pages: 123
PDF File Size: 18.90 Mb
ePub File Size: 4.24 Mb
ISBN: 808-2-23400-806-4
Downloads: 41579
Price: Free* [*Free Regsitration Required]
Uploader: Vudorn

ATTP1 Attansic CPU thermal protection controller chip SOP8

I attansc the AN7 has a thermal probe under the north bridge. You will need to carefully lift this pin from the solder pad.

Webb City, Mo Posts: This is the analog voltage input. If you muck this up and turn your board into a doorstop, don’t come crying to me. When the PSU is shutdown or in standby, this rail is dead, and all of the items connected to the monitor inputs are no longer in a high impedance state.

Add Thread to del. Also make sure that you don’t agtp1 bridge any of the adjacent pins with solder while you are trying to lift this pin. I will have no sympathy. I didn’t think it did. You don’t atgansic to move the jumper though. Where’s the thermal diode? You should thread the jumper first, then solder to the Attansic chip, then finally solder to the Winbond chip. However, be aware that soldering pin 97 and pin back down is rather tricky because of the fine spacing of the pins.

This connects to channel two of the Winbond chip, which means you can now use channel two on pin for something else. Find pin 97 of the Winbond chip. As for the other, yes you should solder pin 4 of the Attansic back down to the mobo. Tie the analog voltage supply for the Winbond chip to the 5vsb rail instead of the 5v rail.

  CONFUCIUS THE ANALECTS PENGUIN CLASSICS PDF

Also note that, because you are now monitoring the thermal diode directly, the thermistor in the socket is now rather pointless. It’s already in the right place. BB code is On. Well, I’ve solved that problem. As a result, when you tie the Temp 3 input to the thermal diode while the Attansic chip is hooked up, it causes the Attansic chip to think that the CPU has exceeded safe temp limits. Check out our sttansic site! It is the attamsic pin from the top right corner of the chip going down the right side of the chip, when viewed as described above.

Find pin of the Winbond chip. I’ve got pretty steady hands and it took me three tries to get the jumper soldered correctly without bridging solder to the other pins. This is the top right pin on the Attansic chip, when viewed with the mobo oriented as described above.

That’s all there is to it. Solder to pin 61 first, then pin Soldering on these quad flat packs is a real PITA!

Attansic ATTP1 datasheet & applicatoin notes – Datasheet Archive

Our members offer you their FAQs! Apply a dollop of gel type super glue or some other fastening agent to each of your jumpers to near pin 97 and pin to keep them from flexing too much and breaking the pins off the chip. The wire will need to be about 8 cm 3″ long. The possibilities are endless! So what is the solution? It is the pin at the very atyp1 left corner of the Winbond chip on the top, when viewed as described above.

  ERNESTO EKAIZER PDF

If you have previously modded your mobo to read the thermal diode, you MAY atyansic that your temps are degrees higher than they used to be.

ATTP1_1.3.pdf

I just have you solder directly to the pin because it is simpler to explain. Find pin 61 of the Winbond chip. The time now is That is one of the reasons I did it the way I did, so that you could undo it if necessary.

It didn’t change my temp readings at all, but it is theoretically possible for there to be a slight change in the reading. These pins are VERY delicate! The original mod involved disabling the Attansic chip protection because simply hooking the thermal diode from the CPU to the Winbond chip would result in the system not powering up, and the familiar two-tone “You’ve got something really mucked up” siren.

The jumper wire will need to be about 3.

As for the northbridge, does it have a thermal diode? In my case, I actually took a chance with my CPU to try it out. If I understand your question correctly, then to restore the mobo back to default, you simply have to remove the mod.